Search:

Type: Posts; User: BIV

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    1,547

    I'm not picky w/weight (viscosity). Usually use...

    I'm not picky w/weight (viscosity).
    Usually use ATF(5W) or 10W . 20W max.
    Usually run 6" from top compressed & bled. Starting point.
    If it's too "squishy" I'd recommend more spring preload (or...
  2. Thread: BIV 2016 Schedule

    by BIV
    Replies
    0
    Views
    1,873

    BIV 2016 Schedule

    http://www.dragbike.com/bikes-in-the-valley-2016-drag-race-schedule/
  3. Replies
    9
    Views
    3,054

    The one we did was Busa shock w/GSXR extended...

    The one we did was Busa shock w/GSXR extended arm.
    Much cleaner than the 1150 shock "carriage" set up.
    The stock Busa shock reservoir does want to contact the battery box.
  4. Replies
    2
    Views
    971

    Can't bore out to desired wall thickness?

    Can't bore out to desired wall thickness?
  5. I think you need the gear and the housing.

    I think you need the gear and the housing.
  6. Thread: RPM Gauge

    by BIV
    Replies
    3
    Views
    1,018

    '78 is probably cable driven. Electronic would...

    '78 is probably cable driven.
    Electronic would be more accurate.
    Or get a new cable.
  7. Replies
    5
    Views
    1,427

    I wear Hein Gericke but I had to get the pants to...

    I wear Hein Gericke but I had to get the pants to jacket zipper modified to full circle per NHRA rules.
    Best advice is don't cheap out on safety gear!
    In case you ever end up using it!
  8. I know on the Suzuki's if you just connect the...

    I know on the Suzuki's if you just connect the clutch switch wires together the ECU thinks the clutch is in and will limit the performance.
    Should be good build w/quality parts.
  9. Replies
    5
    Views
    1,427

    Vanson and Bates seem most popular for custom...

    Vanson and Bates seem most popular for custom fit.
    MPS has Bracket Racer Leathers
  10. Replies
    7
    Views
    1,577

    Those work fine. Can Guhl open the ECU and...

    Those work fine.
    Can Guhl open the ECU and reprogram it?
  11. Replies
    7
    Views
    1,577

    MPS fuel kill. Killing spark or fuel will work,...

    MPS fuel kill.
    Killing spark or fuel will work, sometimes killing the spark may create a pop @ shift.
  12. Replies
    1
    Views
    996

    Hardware Store

    Hardware Store
  13. Replies
    3
    Views
    1,319

    Like Steve said I use the tail shaft of a vernier...

    Like Steve said I use the tail shaft of a vernier caliper with the valve installed w/just the small spring.
    Al Omond showed a design for a higher tech method earlier in this section.
  14. Replies
    5
    Views
    1,326

    While the GS and KZ platform have proven...

    While the GS and KZ platform have proven themselves, they need expensive professionally built crankshafts.
    The Hayabusa would require very little maintenance or modifications. Good Gen 1 Busa's can...
  15. Replies
    5
    Views
    1,326

    Hayabusa, low maintenance, high return on...

    Hayabusa, low maintenance, high return on investment.
    I would go with Marion Ford @ FBR Shop.
    (Or me )
    Stock Busa motor in FBR shop chassis easy 8's.
  16. Replies
    10
    Views
    2,655

    I measure the installed height w/tailshaft of...

    I measure the installed height w/tailshaft of vernier caliper.
    I have the Proform 0-300 tester and it seems to work fine (I was apprehensive when buying).
  17. Thread: OLD School

    by BIV
    Replies
    1
    Views
    1,849

    OLD School

    https://instagram.com/p/5ryef8Oeds/
  18. Replies
    6
    Views
    1,239

    The stock clutch pushed the pressure plate out...

    The stock clutch pushed the pressure plate out from the LEFT side.
    With that type cable conversion you need spacer.
    Stock plates fine.
  19. Replies
    6
    Views
    1,239

    Stock clutch. Has the buttons in the pressure...

    Stock clutch.
    Has the buttons in the pressure plate for a snowflake lock up that isn't there.
    Maybe cable conversion?
  20. Thread: June 2015 Results

    by BIV
    Replies
    0
    Views
    1,058

    June 2015 Results

    http://www.dragbike.com/bike-in-the-valley-prevails-against-mother-nature/
  21. Thread: Go b.ob!

    by BIV
    Replies
    0
    Views
    2,738

    Go b.ob!

    Bob Carlson MDIR IDBL MTC Summernationals 2 wins & 1 runner up.
    http://www.mirockracing.com/idbl/results/2015/race_2_mdir/friday/IMG_1227.JPG
  22. Thread: May 2015 Results

    by BIV
    Replies
    0
    Views
    796

    May 2015 Results

    http://www.dragbike.com/bikes-in-the-valley-may-results/
  23. Thread: 6.98

    by BIV
    Replies
    0
    Views
    1,246

    6.98

    Richard Gadson @ MDIR


    http://www.dragbike.com/wp-content/uploads/15_0429_idbl_Rich_Gadson.jpg
  24. Thread: Grimeca calipers

    by BIV
    Replies
    8
    Views
    2,190

    Yeah, I heard Grimeca might be done. Seems like...

    Yeah, I heard Grimeca might be done.
    Seems like a good time for someone to step up with calipers (and parts!)
  25. Thread: Grimeca calipers

    by BIV
    Replies
    8
    Views
    2,190

    Koenig? PMFR is back. In FLA. New owner.

    Koenig?
    PMFR is back. In FLA. New owner.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4