Search:

Type: Posts; User: jtodd5781

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Camshafts

    by jtodd5781
    Replies
    1
    Views
    1,864

    Never mind, I found the specs in an old Schnitz...

    Never mind, I found the specs in an old Schnitz catalog.
  2. Replies
    2
    Views
    1,850

    Bad ignition plate or wiring?

    Bad ignition plate or wiring?
  3. Thread: Camshafts

    by jtodd5781
    Replies
    1
    Views
    1,864

    Camshafts

    I have on hand a Cam Motion Z11 camshaft, does anyone know the specs for it?
  4. Replies
    3
    Views
    1,248

    Talk to Paul Gast in regards to the Lectrons.

    Talk to Paul Gast in regards to the Lectrons.
  5. Replies
    3
    Views
    1,248

    Mikuni makes power jet kits and there are others...

    Mikuni makes power jet kits and there are others available too.
  6. Replies
    10
    Views
    2,705

    Yes, that is the height you measure as the spring...

    Yes, that is the height you measure as the spring won't go past that unless you have small diameter shims that go between spring bolt boss and the lockup plate, even then you would just add the...
  7. If you are running a stock busa motor, why would...

    If you are running a stock busa motor, why would you want to mess with a 24V system? If you have a lot of electronics to run, just get yourself a 20 Cell LiFe battery.
  8. Thread: Gearing

    by jtodd5781
    Replies
    1
    Views
    1,155

    Do you have Microsoft Excel? If so, I have a...

    Do you have Microsoft Excel? If so, I have a formula that you plug in tire diameter, front and rear sprockets, and shift RPM and it will tell you your MPH in each gear, depending on which...
  9. Replies
    15
    Views
    2,652

    I'm trying to get my bike back to being low...

    I'm trying to get my bike back to being low maintenance as it use to be when I was running a 5.5" slick with a spoke wheel as I am usually by myself when I go racing. The 5.5" slick worked great when...
  10. Replies
    15
    Views
    2,652

    Well, I figured there would be with the added...

    Well, I figured there would be with the added weigh of the tube.
  11. Replies
    15
    Views
    2,652

    How much of a performance reduction do you think...

    How much of a performance reduction do you think there is with running tubes vs without?
  12. Replies
    15
    Views
    2,652

    What size tube would you use for a 7x18" M/T tire?

    What size tube would you use for a 7x18" M/T tire?
  13. Replies
    1
    Views
    1,157

    Dyna 4000 ignition testing

    I noticed that Schnitz doesn't sell the DCS-T01 ignition tester anymore. I was wonder, will the MSD ignition tester work on the Dyna 4000? If so, which one of their testers work? Thanks in advance.
  14. Thread: KZ 1000P

    by jtodd5781
    Replies
    8
    Views
    1,904

    Yes it is a J model. The J model cases were used...

    Yes it is a J model. The J model cases were used from 1981 to 2005.
  15. Replies
    7
    Views
    1,693

    Why would you want to run that much current...

    Why would you want to run that much current through a kill switch?
  16. Replies
    10
    Views
    1,297

    You may want to be careful with the cheap solid...

    You may want to be careful with the cheap solid state relays such as the SSR-25-DD by Fotek. Do some research and find out what others have said about them, remember, generally you get what you paid...
  17. Replies
    10
    Views
    1,297

    If all your powering up is a shift solenoid,...

    If all your powering up is a shift solenoid, which is only going to draw less than maybe a couple hundred milliamps, I suggest using a power mosfet, they are only about a $1 each vs. $80., plus the...
  18. Replies
    10
    Views
    1,297

    Depending on what your application is, the much...

    Depending on what your application is, the much cheaper alternative would be to use a high power mosfet.
  19. Replies
    10
    Views
    1,297

    They are a little pricey through MPS.

    They are a little pricey through MPS.
  20. Replies
    10
    Views
    1,297

    What are you going to be powering with the solid...

    What are you going to be powering with the solid state relays? I've been looking at them too. Have you looked at the Crydom D1D40?
  21. Replies
    9
    Views
    3,296

    I thought it looked rather sad. I guess we won't...

    I thought it looked rather sad. I guess we won't know the true numbers till they post the points.
  22. Replies
    9
    Views
    3,296

    I think the purse structure is having an effect...

    I think the purse structure is having an effect on the number of entrants. Only 15 for Pro ET? There were 51 last year in Bradenton. That's pitiful.
  23. Replies
    15
    Views
    4,459

    I use to run a 5.5 tire with my low compression...

    I use to run a 5.5 tire with my low compression kick start 1394cc KZ, I was able to run a best 60 ft of 1.28 and was usually around 1.31 launching it at 6800, It ran 9.20 without NOS and 8.48 with. I...
  24. Replies
    3
    Views
    1,161

    I called Dynatek last week and they told me that...

    I called Dynatek last week and they told me that they don't have a part number for the terminal socket, just for the whole harness. They told me that they have the harnesses made by supplier and that...
  25. Replies
    3
    Views
    1,161

    Dyna 4000 Super Pro Connector

    I'm in the process of rewiring my dragbike and instead of resplicing in to the main harness coming from the Dyna 4000 Super Pro connector, I would like to replace the wire and the female connector...
Results 1 to 25 of 336
Page 1 of 14 1 2 3 4