Search:

Type: Posts; User: riceburner

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    1,850

    be sure the pick up are plugged in

    be sure the pick up are plugged in
  2. Replies
    2
    Views
    1,943

    fix the shim stack, keep about .040" before bind...

    fix the shim stack, keep about .040" before bind at full lift. IF you loose the seat pressure you are looking for you might need some other springs.
  3. Replies
    3
    Views
    1,341

    install the valve spring and measure the height.

    install the valve spring and measure the height.
  4. Replies
    1,565
    Views
    116,031

    https://www.youtube.com/watch?v=zc4aeCBpsRQ

    https://www.youtube.com/watch?v=zc4aeCBpsRQ
  5. Replies
    1,565
    Views
    116,031

    https://www.youtube.com/watch?v=z5lhM_hai98

    https://www.youtube.com/watch?v=z5lhM_hai98
  6. Replies
    4
    Views
    2,335

    You don't loose any torque (that is a matter of...

    You don't loose any torque (that is a matter of engine tune, not crankshaft weight), the crank might loose some inertia (read could bog) that could slow down initial acceleration, but...a light crank...
  7. Replies
    1
    Views
    1,319

    somebody will win, and allot more will loose.

    somebody will win, and allot more will loose.
  8. Replies
    3
    Views
    5,310

    So be it...

    So be it...
  9. Replies
    9
    Views
    2,133

    it may have been a two part epoxy, but I'm pretty...

    it may have been a two part epoxy, but I'm pretty sure that Chip put it back in with JB weld (which is a two part epoxy).
  10. Replies
    9
    Views
    2,133

    we had one come out one time, luckily it only...

    we had one come out one time, luckily it only fell down and stuck to a steel plate, we re-installed with some jb weld and has been in place for years.
  11. Replies
    5
    Views
    1,569

    I made my own.

    I made my own.
  12. Replies
    10
    Views
    1,297

    solid state relays are superior to the old...

    solid state relays are superior to the old mechanical one, good choice in making the change over.
  13. Replies
    12
    Views
    3,910

    Wasnt there a board member called...

    Wasnt there a board member called "Kawi1500Vortex2" (or something like that), he should have the answers you are looking for.
  14. Replies
    16
    Views
    3,603

    Just using that term by itself leaves the window...

    Just using that term by itself leaves the window way open for interpretation.

    Setting a set of carbs maybe more of a challenge to set up, but when you are done the final product will run better,...
  15. Replies
    16
    Views
    3,603

    I think there are a boat load of successful blow...

    I think there are a boat load of successful blow through KZ and Z1's out there.
  16. Replies
    3
    Views
    1,127

    But the 14 is a much stronger base from cases to...

    But the 14 is a much stronger base from cases to transmission, in the end you pay near the same amount for the same performance no matter what the base (except a Harley), the question is how you...
  17. Replies
    6
    Views
    2,137

    you want to have atmospheric pressure on top of...

    you want to have atmospheric pressure on top of the gasoline in the float chamber in order for the fuel to be pushed up through the jets into the low pressure area of the venturi of the carburetor,...
  18. Replies
    9
    Views
    4,264

    I thought you were going to keep that...

    I thought you were going to keep that conversation between us?
  19. Replies
    28
    Views
    7,524

    valve control keeps shims in place

    valve control keeps shims in place
  20. Replies
    28
    Views
    7,524

    500 lift springs have fewer windings, because of...

    500 lift springs have fewer windings, because of that basic design they are going to fatigue quicker than a spring that has more coils.

    Run valve clearance on the loosest end of the spec as...
  21. Replies
    28
    Views
    7,524

    There were design changes in the shim on top...

    There were design changes in the shim on top tappets on the later bikes that used that style for valve clearance that helps keep the shim in place making it safer to run with larger cams and higher...
  22. Replies
    5
    Views
    1,747

    I wouldnt go any smaller than a 14, that would...

    I wouldnt go any smaller than a 14, that would still be pretty tight for that chain.
  23. Replies
    28
    Views
    7,524

    base gasket surface is different between the J...

    base gasket surface is different between the J and KZ
  24. Replies
    28
    Views
    7,524

    You will need to match the base gasket surface of...

    You will need to match the base gasket surface of the KZ to the J case, weld a boss across the cam chain galley where the idler goes then machine to fit.

    Works great, but does require welding and...
  25. Replies
    6
    Views
    1,606

    loose on the swing arm is not good

    loose on the swing arm is not good
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4